Tie Bar Spacing 26 "x 26", Platen Size 37.6" x 37.6", Daylight Max 45.3, Min Mold Height 12.6, Clamp Stroke 32.7, Voltage 460
Dimensions 262.6" x 63" x 81.5", Weight 24,030, Equipped With NC9300T Control, Hydraulic CP, RI
$74,500.00
Ref No: 785588
Tonnage: 309.0
Shot Size: 29.9
1998 Cincinnati Ferromatik K275S
Distance Between Tie Bars 24.80" x 24.80", Platen Size 38.19" x 38.19", Mold Openign Stroke 33.46", Mold Installation Height 13.78", Daylight Max 47.24", Equipped With Ferromatik Control
$26,500.00
Ref No: 785400
Tonnage: 302.0
Shot Size: 31
2001 Arburg 630S-2500-1300
Distance Between Tie Bars 24.8" x 24.8", Platen Size 35.43" x 35.43", Clamping Stroke 23.62", Min Mold Height 11.81"
Max Daylight 35.43"-51.18", Equipped With Selogica Microprocessor , Control, RI, Air Blow, Six Additional Heat Zones, Vacuum Receiver, CP, HKO
$74,500.00
Ref No: 784870
Tonnage: 300.0
Shot Size: 29
1999 Cincinnati VT-300-29
Distance Between Tie Bars 25.2" x 24.6", Platen Size 36.8" x 36.2", Max Daylight 48", Max/Min Mold Height 25.2"/7.9", Equipped With VSX Control, SBI Interface, HKO, RI , CP
Platen Size 35.67" x 35.67", Tie Bar Spacing 25.04" x 25.04", Clamp Sroke 23.62", Mold Thickness 7.87"-25.98", Equipped With CC100 Control, HKO, High Speed Machine, *********ONLY 1,330 HOURS**********
$139,500.00
Ref No: 785684
Tonnage: 300.0
Shot Size: 38.7
2004 Engel TL-1800/300
Platen Size 46.6" x 35", Clamp Type Hydraulic, Equipped With CC100 Control, Dual CP, Motion no Motion
$115,000.00
Ref No: 785683
Tonnage: 300.0
Shot Size: 34.5
1997 Toyo TM-300H
Tie Bar Spacing 28.74" x 28.74", Platen Size 37" x 37", Clamp Stroke 22.8", Min/Max Mold Height 9.84"/25.6", Voltage 480, Weight 28,600, Equipped With PLCS-9 Control, CP
$45,500.00
Ref No: 785238
Tonnage: 300.0
Shot Size: 25.5
2004 Toyo TM-300H2
Platen Size 37" x 37", Tie Bar Spacing 28.74" x 28.74", Clamp Stroke 22.8", Max Daylight 48.4", Min/Max Mold Height 9.84"/25.6"
Weight 28,600, Voltage 480, Equipped With PLCS-11 Control
$95,500.00
Ref No: 785240
Tonnage: 300.0
Shot Size: 32.8
01/00 Toyo TM300H
Distance Between Tie Bars 28.74" x 28.74", Platen Size 37" x 37", Clamping Stroke 22.83", Mold Height (Min/Max) 9.84"/25.60", Ejector , troke 5.51", Electrics 460 Volt, PLCS-9 Control , Air Blow, HKO, CP, 2001 $74,500.00, 2000 $72,500.00
$74,500.00
Ref No: 767102
Tonnage: 300.0
Shot Size: 32.8
2000 Toyo TM300H
Distance Between Tie Bars 28.74" x 28.74", Platen Size 37" x 37", Clamping Stroke 22.83", Mold Height (Min/Max) 9.84"/25.60", Ejector Stroke 5.51", Voltage 460, PLCS-9 Control, CP
$69,500.00
Ref No: 745705
Tonnage: 300.0
Shot Size: 32.8
1993 Trueblood Vertical Shuttle Table
Screw Diaemeter 3", Screw L/D 20:1, Min/Max Daylight 18"/48", Stroke 30", Max Mold Space 40" x 64", Centerline of Injection 14"-24" Adjustable, Voltage 480V, Equipped With Maco 4000 Controls, Adjustable Nozzle Height, Hydraulic Eject, Sprue Break, Two Machines availalbe $39,500.00 Each
$39,500.00
Ref No: 767442
Tonnage: 300.0
Shot Size: 48
1997 Cincinnati Ferromatik K250S
Distance Between Tie Bars 24.80" x 24.80", Platen Size 38.19" x 38.19", Mold Opening Stroke 33.46", Mold Installation Height 13.78", Daylight Max 47.24", Equipped With Feromatik Control, Two (2) Machines Available $24,500.00 Each
$24,500.00
Ref No: 785399
Tonnage: 275.0
Shot Size: 31
1998 Sumitomo SG260M C1250L
Distance Between Tie Bars 22.04718" x 22.04718", Overall Size of Platen 33.07077" x 33.07077", Opening Stroke 8.464541"~22.24403", Mold Space 8.267692"~20.07868", Dry Cycle Time 1.8 sec, Machine Dimensions 277.2" x 64.4" x 89.5", Machine Weight 22,000 Lbs, Equipped With NIV Control, HKO , CP, (4) Four Machines Available $22,500.00 Each
$22,500.00
Ref No: 785420
Tonnage: 260.0
Shot Size: 23.8
2006 Toshiba ISG250V21-10
Platen Size 34.2" x 32.2", Tie Bar Spacing 24" x 22", Clamp Stroke 31.5", Min/Max Daylight 10.2"/41.7", Ejector Stroke 5.1", Equipped With: Injectvisor V21 Control, HKO, CP, Dual Air Blow , Motion no Motion
$96,000.00
Ref No: 785973
Tonnage: 250.0
Shot Size: 16
2000 JSW J245ET
Distance Between Tie Rods 22.83" x 22.83", Mold Thickness 9.06-19.69", Daylight Opening 41.34", Equipped With Syscom 1000 Control, HKO
$50,000.00
Ref No: 785712
Tonnage: 245.0
Shot Size: 17.8
2000 Sumitomo SH2200C
Tie Bar Spacing 24 x 22, Platen Size 35 x 33, Daylight Max 42.9, Min Max Mold Height 9.8-22.8, Clamp Stroke 20.07, Voltage 460, Dimensions 225" x 65.7" x 89.8", Weight 8.1 Meric Ton, Equipped With N7 Control, Hydraulic CP, Eject During Mold Open, External Memory Card Interface
$34,500.00
Ref No: 785579
Tonnage: 243.0
Shot Size: 23.8
1997 Toyo TM-245H-17
Tie Bar Spacing 24.02" x 24.02", Platen 32.28" x 32.28", Clamp Toggle, Clamp Stroke 20.47", Motor HP 40, Min/Max Mold Height 9.84"/25.59", Dimensions (L x W x H) 233.6" x 54.6" x 82.1", Weight 10.5 Tons, Equipped With PLCS9 Control, HKO, Hydraulic CP
$39,500.00
Ref No: 785599
Tonnage: 242.0
Shot Size: 17.5
1997 Nissei FN5000-71A
Tie Bar Spacing 23.2" x 23.2", Platen Size 33.5" x 33.5", Clamp Stroke 29.9", Daylight Max 41.3", Min Mold Height 11.4", Ejector Stroke 4.7" Equipped With NC9000 Control, HKO, CP, Air Blow , Two Machines Available $39,500.00 each
$39,500.00
Ref No: 784874
Tonnage: 239.0
Shot Size: 23.5
2005 Demag Van Dorn HT 230/560-1220
Distance Between Tie Bars 22" x 22", Platen Size 32" x 32", Ejector Stroke 4.5, Daylight Max 42", Mold Thickness-Min 7", Weight 21,300 lbs, Dimensions (l x w x h) 23' x 5' x 6'6", Equipped With Pathfinder 5000 Control, RI, CP, !!!!ONLY 11,000 HOURS!!!!
Find the Right Piece of Equipment for the Plastic Injection Molding You Need
At K.D. Capital, we carry a variety of tools and equipment that your company needs to run successfully. One of the many pieces of equipment we offer is the plastic injection molding machine. We have a good selection of different years and manufacturers, and all the machinery we carry is in top condition.
We make your search for an injection molding machine as simple as possible by providing you with several different ways to conduct your search. By clicking on any of the links listed on this page, you can quickly see the different injection molding machines by year, make, price, model, shot size or ton. We carry some of the most trusted names in the business, so you can be sure the machine you receive from us will provide you with the performance you need.
If you have any questions about the different plastic injection molding machines we sell, you call 800-922-1674 if you're in the United States or 480-922-1674 if you're calling internationally. You can also email us at customerservice@kdcapital.com. If you don't see the exact product you're looking for, just fill out the form on our "If we don't have it, we'll find it page." We'll conduct an extensive search to look for the precise injection molding machine you want and will let you know the different options available. With over 100 years in the business, you can trust the quality of the machines and services K.D. Capital provides.
